![]() ![]() Why is my pressure washer spraying without pulling the trigger? Although, a quick-connect coupling would certainly make the nozzle disconnect from the high pressure hose much faster. I took the two pieces of the handle and placed the spring in between them. The bolt is hard to remove, but it just unscrews off of the handle. ![]() I had to use the pliers to pull the trigger mechanism out of the handle, and then I was able to remove the spring and the “bolt” that holds the head-on. Once I got the two screws off, the head was free. I would recommend having a friend hold the trigger wand and pull it back to keep the head from twisting off with the clamp. I had to use a vice grip on the top of the “c” clamp to twist it off. The head is held onto the trigger with a “c” clamp.Īlso See Can you use an air compressor as a pressure washer? The harder part is removing the washer head from the wand trigger. The first thing to do is to remove the trigger from the wand pressure hose. Here’s how I got my pressure washer wand unstuck. By following these simple tips, you can keep your pressure washer wand in good working condition for years to come. Once you have identified the problem, you can take steps to prevent it from happening again in the future. You may also need to replace the O-ring on the wand if it is damaged. If water is flowing out of the wand, check the filter screen to see if it needs to be replaced. Another possible cause is an inlet filter that is not properly installed or that has become clogged. The most common cause is that the low pressure nozzle is not properly secured. Although there are several ways to prevent this from happening again, I’ll show you what I did that made my next time with the pressure washer a lot easier.Ī pressure washer trigger wand can become loose for a variety of reasons. If you’re reading this, you’ve probably just gone through the ordeal of getting your pressure washer gun not working. This is a common problem that plagues homeowners who use pressure washers. How do I fix the pressure washer wand to prevent it from happening again? When this happens, you need to clean the sprinkler head before you can use it again. One of the biggest reasons is that foaming detergent can clog the holes on plastic and metal wands. A pressure washer wand or gun stuck open gets stuck for several reasons. In most cases, this is caused by blocked holes in the wand and tip. When using a pressure washer, the wand can get stuck. You were going along just fine cleaning the driveway, car, or patio chair, and then nothing your pressure washer wand gets stuck and stops spraying water. Regardless of what’s going on, there are a few things you should try before running straight to buy a new wand to finish all the pressure washer machine jobs.Īlso See Is Your Pressure Washer Pull Cord Stuck or Hard To PullĪlso Read: How to Start a Pressure Washer (Step By Step Guide)Īlso worth reading: How to Treat a Pressure Washer Injury: Don’t Let the Scars Fester! What makes a pressure washer spray wand stick?Ī pressure washer wand sticking is frustrating and something that can just kill your day. Be sure to check the unloader valve and pump and any sign of trouble. If the pump appears to be damaged, it will need to be replaced. If your pressure washer has low or no pressure, check the pump for damage and leaks. If the nozzle tip is still blocked, you may need to replace it.Īnother possible cause of low pressure is a damaged pump. Once it has soaked for a few minutes, use a toothpick or other sharp object to clear any debris from the tip. To clean the nozzle tip, simply remove it from the wand and soak it in a solution of vinegar and water. The nozzle tip can become blocked by dirt, rust, or other debris, and this can restrict the flow of water, resulting in low pressure. This can be caused by a number of factors, but the most likely culprit is a blocked nozzle tip. One of the most common power washer problems is low or no pressure coming from the wand. Whether it’s your pressure washer soap nozzle, the pressure washer unloader valve stuck, the pressure washer pump sticking or your power washer spray gun getting jammed. Pressure washer tools sometimes get stuck when working on your projects. Why does this high pressure tool get stuck? Why does my pressure washer wand not work? ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |